套管开窗侧钻技术在贵州地热钻井中的应用
DOI:
作者:
作者单位:

贵州省地质矿产勘查开发局111地质大队,贵州省地质矿产勘查开发局112地质大队,贵州省地质矿产勘查开发局112地质大队,贵州省地质矿产勘查开发局111地质大队,贵州省地质矿产勘查开发局111地质大队,贵州省地质矿产勘查开发局112地质大队

作者简介:

通讯作者:

中图分类号:

TE243 .9;TE249

基金项目:

贵州省社会发展科技攻关资助项目“贵州复杂地层深井钻探工艺应用研究”(编号:黔科合SY字\[2015\]3002);贵州省地矿局地质科研资金资助项目“双壁钻杆空气潜孔锤局部反循环钻井工艺在贵州地热深井中的应用研究”(编号:黔地矿科合\[2017\]01)


Application of Sidetracking in Casing in Guizhou Geothermal Drilling
Author:
Affiliation:

111 Geological Brigade of Bureau of Geology and Mineral Exploration and Development Guizhou Province,112 Geological Brigade of Bureau of Geology and Mineral Exploration and Development Guizhou Province,112 Geological Brigade of Bureau of Geology and Mineral Exploration and Development Guizhou Province,111 Geological Brigade of Bureau of Geology and Mineral Exploration and Development Guizhou Province,111 Geological Brigade of Bureau of Geology and Mineral Exploration and Development Guizhou Province,112 Geological Brigade of Bureau of Geology and Mineral Exploration and Development Guizhou Province

Fund Project:

Social development of Guizhou Province scientific and technological project "Guizhou complex formation of deep well drilling technology research and application" (number: Guizhou, SY [2015]3002); application research project supported by Guizhou Provincial Bureau of Geology and mineral geological research funds double wall drill DTH hammer reverse circulation drilling technology in Guizhou local geothermal wells "(number: Guizhou Department of Geology and mineral resources) [2017]01

  • 摘要
  • |
  • 图/表
  • |
  • 访问统计
  • |
  • 参考文献
  • |
  • 相似文献
  • |
  • 引证文献
  • |
  • 资源附件
  • |
  • 文章评论
    摘要:

    普安县江西坡地热井在钻进到井深907.91 m时遇到了卡钻事故,解卡失败后,进行倒扣处理,剩余75.53 m“落鱼”无法取出,“鱼头”位置井深832.38 m。为绕开“鱼头”位置继续钻进,必须进行开窗侧钻。在已经下套管固井的情况下,选用了DXQ210/H型导斜器作为导斜工具,使用KCXZ216型铣锥作为磨铣开窗工具,进行了套管内侧钻开窗作业。在分析事故概况的基础上,介绍了导斜器的工作原理和套管内开窗侧钻的技术方案,总结了施工作业中的注意事项,最终侧钻成功并顺利钻进到2364.56 m完钻。

    Abstract:

    Sticking accident happened at the drilling depth of 907.91m in Jiangxipo geothermal well, back-off was used after releasing failed, the remainded 75.53m drilling tool could not be taken out and the top end of the drilling tool was at the depth of 832.38m. It is necessary to adopt sidetracking to bypass the top end of the drilling tool for continue drilling. In the case of casing cementing completion, sidetracking window from inside casing was carried out with DXQ210/H type deflecting device selected as the deflecting tool and KCXZ216 type taper miller as milling tool. Based on the analysis on the general situation of the accident, the paper introduces the working principle of the deflecting device and the technical scheme of sidetracking window from inside the case and summarizes the attentions in the construction operation. The sidetracking is smoothly completed at the depth of 2364.56m.

    参考文献
    相似文献
    引证文献
引用本文

李奇龙,张承飞,宋继伟,等.套管开窗侧钻技术在贵州地热钻井中的应用[J].钻探工程,2018,45(7):6-9.
LI Qi-long, ZHANG Cheng-fei, SONG Ji-wei, et al. Application of Sidetracking in Casing in Guizhou Geothermal Drilling[J]. Drilling Engineering, 2018,45(7):6-9.

复制
分享
文章指标
  • 点击次数:
  • 下载次数:
  • HTML阅读次数:
  • 引用次数:
历史
  • 收稿日期:2018-02-01
  • 最后修改日期:2018-06-19
  • 录用日期:2018-06-26
  • 在线发布日期: 2018-08-07
  • 出版日期: